24/7 Emergency Dispatch · (866) 737-2830
NJ Master HVACR Contractor Lic. #19HC00145700 · Bonded · Insured
Furnace Repair · Gas · Oil · Electric

No heat tonight?We run 24/7 for this.

Furnaces fail below freezing on a Sunday night. That's why igniters, flame sensors, control boards and blower motors are already on the truck — about 90% of what a no-heat call needs.

  • Dispatch 24/7
  • Emergency 90-min or $50 off
  • Every visit combustion tested
4.6 · 445 Google reviews NATE certified · EPA 608/609 NJ Lic. #19HC00145700
Rescue technicians servicing a gas furnace in a Northern New Jersey basement
Passaic County · no-heat call cleared the same night
Dispatch live
24/7
Winter no-heat calls
get top priority

What most companies skip

Every furnace visit gets combustion tested

A furnace burns gas inside your house. Whether it's burning it correctly is a measurement, not an opinion — so we measure it, every visit, and you get the numbers.

Combustion analysis · included on every furnace visit
Carbon monoxide
CO in flue gas
The one that matters most. A cracked heat exchanger or incomplete burn shows up here before anyone in the house feels it.
Draft
Flue draft pressure
Confirms combustion gases are actually leaving the building rather than spilling back into the room.
Gas pressure
Manifold & inlet
Over-fired or under-fired furnaces waste gas, run hot, and shorten the life of the heat exchanger.
Temperature rise
Supply vs return
Outside the manufacturer's range means an airflow problem — and airflow problems are what crack heat exchangers.

This is standard on every furnace call, including a $189 tune-up. It's how we catch a dangerous condition while it's still a gasket, not a hospital visit — and it's the reason we can tell you honestly whether a furnace is safe to keep running.

Yellow flame instead of blue? Stop and call.

A healthy gas flame is steady and blue. Yellow or lazy flame means incomplete combustion, and incomplete combustion can produce carbon monoxide. The same goes for soot around the unit, a burner that won't stay lit, or a CO detector that has sounded even once.

Shut the furnace off at the switch, open a window if you can, get everyone out if anyone feels dizzy, headachy or nauseous — and call us. Dispatch runs 24 hours and this is the call we drop everything for.

Start here

What's it actually doing?

The symptom tells us which parts to load before we leave. Pick yours and you'll see the likely cause and roughly what it takes to fix.

Igniter, flame sensor, or a limit trip

The blower runs but the burner never fires, or fires and drops out. Most often a hot surface igniter or a dirty flame sensor. Sometimes a clogged filter tripping the high-limit switch. If it persists past one cycle, shut it off and call.

Hot surface igniter
$285–$389
Flame sensor
$165–$249
On site
30–90 min

Thermostat, transformer, or control board

Nothing happens at all. We work back through it with a multimeter rather than swapping parts and hoping — thermostat wiring first, then the transformer, then the board, because those are three very different numbers.

Control board
$485–$795
Diagnosed by
Multimeter, not guesswork
Urgency
Same day in winter

Usually cheap, occasionally structural

A dirty flame sensor is the common one and it's an inexpensive clean. Overheating from a clogged filter is next. But a furnace that was oversized for the house short-cycles forever, and no part fixes that — we'll tell you which one you have.

Flame sensor
$165–$249
Diagnosis
About 30 min
Repair or replace
Usually a cheap fix

Blower or inducer bearings

Screeching is normally blower motor bearings. A rattle can be as simple as loose ductwork. Bearings are replaceable and we don't treat a noisy blower as a reason to sell a whole furnace.

Blower motor
$595–$1,195
Inducer motor
$595–$895
Repair or replace
Repair the motor

Combustion problem — get it measured

Yellow flame means incomplete burn, which can produce carbon monoxide. A climbing gas bill points at heat exchanger fouling, an oversized unit, or duct leaks. Both are answered by the same combustion analysis, and both are worth answering now.

What we measure
CO, draft, gas pressure
Included with
Every furnace visit
Urgency
Stop using it — call

Help me choose

Furnace efficiency tiers

If it's replacement territory, this is the whole decision. No upselling and no scare tactics — Northern NJ winters are long enough that the maths does the arguing.

FeatureStandard 80% AFUE92–95% Single-Stage95%+ Two-Stage / Variable
AFUE rating80%92–95%95–98.5%
Annual fuel savings vs 80%Baseline12–18%18–25%
Install cost$4,995–$7,495$6,995–$9,995$8,995–$12,995
Best forBudget replacementMost homes Most pickedNorthern NJ winters, large homes
VentingMetal flue, chimneyPVC sidewallPVC sidewall + condensate
Lifespan15–20 years15–20 years15–20 years
NJ rebate eligibleNoSometimesYes — up to $1,000

Flat rate, no bait

What it costs

Real ranges. The final quote is always given on site after diagnosis, and no work starts without your written approval.

$79Diagnostic visit
  1. NATE-certified tech on site, not a subcontractor
  2. Combustion tested and the fault identified
  3. Waived entirely when you go ahead with the repair
Flame sensor
Clean or replace. The cheapest common cause of a furnace that lights then quits
$165–$249
Hot surface igniter
The single most common no-heat repair we do in January
$285–$389
Control board
Gas furnace board. Diagnosed on a meter before it's condemned
$485–$795
Inducer motor
Draws combustion gases through the heat exchanger and out the flue
$595–$895
Blower motor
By motor type — PSC or ECM variable-speed changes the number
$595–$1,195
Annual tune-up
Combustion analysis, gas pressure, flame sensor clean, condensate trap, blower amp draw, filter, leak test. About 75 minutes
$189
Furnace replacement — 80% AFUE
Permitted, inspected, manufacturer warranty registered same day
$4,995–$7,495
Furnace replacement — 95%+ AFUE
PVC venting and condensate. Often rebate-eligible
$6,995–$10,995

Prices reflect typical ranges in Northern NJ as of 2026. Permit fees, complex access and emergency hours adjust the final quote — always disclosed up front. Replacement quotes follow a heat-load calculation, not a guess at the box size. Workmanship is warranted 1 year on repairs and 2 years on premium installs; manufacturer parts warranties are typically 10 years with a 20-year heat exchanger on premium models, registered by us within 60 days so the coverage actually activates. NJ Master HVACR Contractor Lic. #19HC00145700 · bonded · insured.

How the visit goes

Four steps, no mystery

  1. A person answers

    Not a call centre. Winter no-heat calls get top priority, and dispatch runs every hour of the night.

  2. We diagnose and measure

    NATE-certified tech, fully stocked truck. Combustion analysis on every visit — CO, draft and gas pressure, as actual data.

  3. Honest fix-or-replace call

    A $200 igniter on an eight-year furnace is a repair, and we'll say so. A $1,800 board on a sixteen-year-old unit usually isn't.

  4. Fixed the same visit

    About 90% of the parts a no-heat call needs are already on the truck, so same-visit repairs are the rule rather than the exception.

Real work

Our jobs, not stock photos

Gas furnace installed by Rescue in a New Jersey basement, flue and gas line visible
Gas furnace replacement — permit pulled, inspection coordinated, warranty registered the same day.
Boiler and heating system installed by Rescue in a New Jersey basement
Heating install with new venting and near-boiler piping.
Rescue Sprinter van on a night call in Northern New Jersey
Nine Sprinter vans, stocked. Night calls in January are normal here.
~90%Of no-heat parts already on the truck.
Every visitCombustion tested — CO, draft, gas pressure.
1–2 yrsWorkmanship warranty; 1 on repairs, 2 on premium installs.
47 townsPassaic, Bergen, Essex, Morris, Hudson and Union.

Real customers

What NJ neighbours say

4.6 across 445 Google reviews. Three of them below.

★★★★★

Furnace died on the coldest night of January. They had a tech here in 45 minutes, diagnosed a hot-surface igniter, replaced it for $325. Heat back on by midnight.

Patricia R.Madison, NJ
★★★★★

Did our full furnace replacement — Carrier 96% AFUE. Permits, install, inspection, registered the warranty. They walked us through the whole thing.

David M.Teaneck, NJ
★★★★★

Tech caught a small CO leak during routine service. Replaced the heat exchanger gasket, tested everything, gave us a printed combustion report. Other companies don't even check.

Helena K.Jersey City, NJ

Questions we get a lot

Cost, timing & dispatch

How much does furnace repair cost?

Most repairs run $165–$1,195 depending on the part. Flame sensor clean or replace $165–$249. Hot surface igniter $285–$389. Control board $485–$795. Inducer motor $595–$895. Blower motor $595–$1,195. Heat exchanger replacement $1,495–$2,995 — at that number, replacing the furnace is usually the smarter move and we'll say so. Everything is flat-rate and written down before work begins.

How much does furnace installation cost in Northern New Jersey?

80% AFUE standard furnace: $4,995–$7,495. 92–95% AFUE high-efficiency: $6,995–$9,995. 95%+ AFUE two-stage or variable premium: $8,995–$12,995. Heat pump conversion runs $11,995–$22,995 with up to $3,500 in stacked rebates. Every replacement is quoted on site after a heat-load calculation, not from the size of the old box.

How fast can you fix a no-heat call in winter?

Tier 1 dispatch zones — Haledon, Paterson, Clifton, Hackensack, Hawthorne, Teaneck, Newark, Montclair — are on site within 60–90 minutes at any hour. Tier 2 — Mahwah, Morristown, Parsippany — runs 2–3 hours. Dispatch is 24/7 from our Haledon HQ and December-to-February no-heat calls get top priority.

How long does furnace installation take?

A direct replacement on the same fuel and similar capacity is one day, roughly 7am to 4pm. A new high-efficiency install needing PVC venting and condensate is one to one-and-a-half days. Furnace and A/C combined is one-and-a-half to two days. A heat pump conversion is two days.

Do you offer financing for furnace installation?

Yes. 0% APR for 12 months on jobs over $1,500 through GreenSky or Synchrony, and 12–84 month fixed-APR plans for larger jobs. Soft credit check with no impact to apply, and most approvals come back in under 60 seconds. Financing stacks with rebates.

Diagnosing the problem

Why does my furnace blow cold air sometimes?

Three causes. It may simply be in a startup or cooldown cycle, which is normal. The pilot may be out or the igniter failed, so the blower runs with no flame. Or it's an overheat shutdown from a dirty filter or blocked vents tripping the high limit. If it persists past one cycle, turn it off and call — cold air means the burner isn't firing.

Why is my furnace short-cycling — turning on and off?

Top causes: an oversized furnace, which is the most common in NJ housing stock and can't be fixed with a part; a dirty filter restricting airflow and tripping the high-limit; a faulty flame sensor letting the flame establish then drop; a bad thermostat or one mounted in the wrong place; or a failing inducer motor. We diagnose it in about 30 minutes.

Is a yellow flame normal?

No. A gas flame should be steady and blue. Yellow means incomplete combustion, which can produce carbon monoxide. Shut the furnace off and call us. The same applies to soot around the unit or a CO detector that has sounded even once — this is a 24/7 call for us, not a next-available appointment.

Should I repair or replace my old furnace?

Three questions. Age — under 12 years usually repair, over 18 usually replace. Which part failed — igniter, flame sensor, capacitor and motors are repair-grade, while a heat exchanger or control board failure on an older unit is replace-grade. And cost — if the repair is over 50% of a replacement, replace it.

How long should a furnace last?

Fifteen to twenty years if it's maintained. We still see 25-year-old units running, but heat exchanger fatigue and efficiency loss usually make replacement the right call somewhere around year 16 to 18.

What does a tune-up include?

Combustion analysis, gas pressure check, flame sensor clean, condensate trap inspection, blower motor amp draw, filter replacement and a leak test. It's $189 and takes about 75 minutes. The combustion analysis is the part most companies skip and the part most likely to catch something dangerous early.

Choosing, permits & rebates

What is AFUE, and what should I get?

AFUE is Annual Fuel Utilization Efficiency — how much of the gas you buy becomes actual heat. The NJ minimum for new installs is 80%. A 92–95% mid-tier unit saves roughly $300 a year against 80% in a Northern NJ winter, and 96–98% premium saves about $150 a year beyond that. Payback on the upgrade is typically five to seven years.

What is the best furnace brand for NJ?

In the order we recommend them: Rheem Prestige for best value with a 10-year parts warranty — we're a Rheem Pro Partner. Carrier Infinity for premium build and a deep NJ dealer network. Trane S9V2 for long-haul reliability. Lennox SLP for the highest-efficiency variable-speed option. Bryant is Carrier-built at lower cost. For a mid-budget home, the Rheem 95 AFUE two-stage is the value pick.

Do you handle oil-to-gas conversions in NJ?

Yes — including above-ground oil tank decommissioning, soil testing where the tank was buried, the new gas line run and the new gas furnace install. All-in it typically runs $7,995–$14,995, with payback in New Jersey usually four to seven years. NJ Clean Energy rebates are often $500–$1,500 on a conversion. We coordinate every permit.

Do I need a permit to install a furnace in NJ?

Yes, it's mandatory under the NJ Uniform Construction Code — a mechanical permit at $75–$250, plus an electrical permit on most installs. We pull them same-day and coordinate the inspection. A furnace installed without a permit voids the manufacturer warranty and creates a liability when you sell the house.

What rebates are available in NJ?

The NJ Clean Energy Program offers $300–$1,200 on 95%+ AFUE furnaces. PSE&G and JCP&L utility rebates add $100–$500. The federal tax credit runs up to $600 on qualifying high-efficiency furnaces at 96%+ AFUE. Stacked, that's often $1,000–$2,500 off a premium install, and we file the paperwork.

Should I replace the A/C at the same time?

Often yes. The indoor coil has to match a modern condenser for the SEER2 rating to actually be achieved. Combined-install labour saves roughly $800–$1,500 against two separate jobs. Manufacturer rebates are richer on matched systems. And if the furnace is 15+ years old, the A/C is usually the same vintage. We quote both ways so you can see it.

What warranty do you provide?

Parts: 10-year manufacturer warranty on Rheem, Carrier, Trane and Lennox premium models, with a 20-year heat exchanger, registered within 60 days — we do that automatically, because coverage doesn't start until someone does. Workmanship: 2 years on premium installs, 1 year standard. Free re-visit if anything fails in the first year.

Coverage

Dispatched from Haledon

Nine stocked Sprinter vans covering 47 towns across Passaic, Bergen, Essex, Morris, Hudson and Union counties.

PatersonPassaic County · ETA 15–25 min
CliftonPassaic County · ETA 15–25 min
HackensackBergen County · ETA 20–30 min
NewarkEssex County · ETA 25–35 min
WaynePassaic County · ETA 25–40 min
MontclairEssex County · ETA 25–35 min
Jersey CityHudson County · ETA 30–45 min
MorristownMorris County · ETA 40–55 min

You might also need

Related services

House getting cold?

Call it in. A real dispatcher, any hour, and the part is probably already on the truck.